Results 11 to 20 of 24
-
7th April 2019, 03:54 AM #11
Is it not more easy to select a normal car within the Truck version ?
It's just a few clicks to change from your motorhome to any other car.
Navcore 9.702 I thought set in the X40 mode give you an extra icon to change the vehicle quite easy
-
15th September 2019, 06:20 PM #12
I tried to copy files to pc, and erase the sdcard. Then copy in sd card from beginning. When I did this, there was two files with 0 kb impossible to erase. Perhaps a cause of virus, I don`t know. I formatted the sd card, without any problem, I copied the files in, and then tomtom worked welll. The problem was in sd card.
-
The Following 1 Users Say Thank You to otin For This Useful Post:
- [ Click To Expand ]
-
pe1agp (15th September 2019)
-
15th September 2019, 06:27 PM #13
-
15th September 2019, 07:03 PM #14
When I changed the map version 1035 instead the 1030 one, I has appeared the not desired restart problem again.
To delete pdis and heard warnings doesn`t give solution for the problem.
- New map 1035 works well erasing old file mapsettings, and begining from zero with this file.
- Old map 1030 works perfectly with old mapsettings file.
- New map 1035 doesn`t work with old file mapsettings extracted from 1030 map.
I always has copied the last file mapsettings.cfg to new map and I never has any problem. It is the first time.
I tried to begin well with 1030 map, and change to 1035. Then crash, it begins to restart y restart.
I don`t want to lose my favorites saved until now. Also, I prefer keep my configuration too, but if it is not possible, it is less serious, I put the configuration again. The worst thing is to put, again, all the warnings of the radars and the pdis, that there are many, but if there is no other remedy ...
My favorites list is more important.
Have you any solution occurs?Last edited by otin; 15th September 2019 at 07:08 PM.
-
15th September 2019, 07:17 PM #15
The use of the old mapsetting.cfg file is as follows.
Start TomTom Home
Connect your TomTom with your PC, connect with the PC if your TomTom asks for it.
Now go to operate my device or something similar.
Plan a short route and let a piece of the demo route run.
Stop the demo and return to the beginning, now your mapsetting.cfg is written in the correct format.
Good luck.
-
The Following 3 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
Alfred_ML (17th September 2019), Nando Rola (15th September 2019), otin (15th September 2019)
-
15th September 2019, 07:49 PM #16
-
The Following 3 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
Alfred_ML (17th September 2019), Jeanet (15th September 2019), Nando Rola (15th September 2019)
-
17th September 2019, 02:52 PM #17
I have re-uploaded the archive of the TT Home Truck 9.702 extension in # 6
-
The Following 2 Users Say Thank You to Alfred_ML For This Useful Post:
- [ Click To Expand ]
-
-
27th February 2021, 09:36 PM #18
Alfred_ML
Would you please upload the "Navcore.9.702.1512362@tomtom.com" folder as I can't find it anywhere as I need it to use Operate My Go in TomTom HOME to fix my mapsettings.cfg file each time I update the map. The link in your post isn't working. I have a GO920T.
-
27th February 2021, 10:47 PM #19
-
The Following 2 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
-
27th February 2021, 11:00 PM #20
Unpack ONLY! the RAR File. Put the Folder in the Section, You found if you start TTH, left Top---under Help--System Information---Profil-Folder---in thisFolder are be a Folder "extensions", put the Folder *.
into.... Good Luck...THX Alfred
...........to late
-
The Following 2 Users Say Thank You to Proukaet For This Useful Post:
- [ Click To Expand ]
-
Universal Firmware Patcher for...
Hello, How can I get into the preboot mode on...