Results 11 to 17 of 17
-
15th August 2021, 04:48 PM #11
The Rider v2 is still mounted on my bike, I can't check it at the moment, but I think you can adjust the preference of the menu bar at the bottom to it?
In bright sunlight, the screen is indeed very difficult to read, but I usually just listen to what is spoken, sometimes at road junctions I try to get a little wiser from the screen.
-
26th August 2021, 11:49 PM #12
Hi, when you turn on the gps with the navcore Rider V5 you find this menu:
[img] [/ img]
Unlike the 9501 that does not offer it, at least the ones that I have tried.
Apart from the files necessary for it to work optimally according to the type of gps chip that your gps has, I have added 42 vehicle symbols (54 in the navcore car & rider and car & rider jukebox) and 34 different map colors, I explain in the tutorial how to change them.
On the other hand, to see only the maximum speed disk allowed on each road you are driving on, you have to follow these steps:
From the main screen --- options --- status bar preferences --- horizontal (or vertical, as you prefer) --- and leave only marked: maximum speed, remaining distance and show lane guidance --- done.
-
The Following 2 Users Say Thank You to Masp For This Useful Post:
- [ Click To Expand ]
-
biggerdave (27th August 2021), Orni (27th August 2021)
-
28th August 2021, 12:36 AM #13
This is how my NC 9501a from on Rider v2 looks
I'll try out your navcore as I can't have big max speed disk only 31/30 format of current_speed/max_speed
-
28th August 2021, 01:34 PM #14
I have installed the navcore 9501 Rider V5 in 3 gps with 3.5, 4.3 and 5 inch screens and in all of them I see the maximum speed disk less in the 3.5 inch gps, so I understand that the limitation is by screen size ... I'm afraid we can't do anything.
-
The Following 2 Users Say Thank You to Masp For This Useful Post:
- [ Click To Expand ]
-
biggerdave (28th August 2021), Orni (28th August 2021)
-
20th September 2021, 06:33 PM #15
My apologies if this is not the right place to ask this questions. I have Rider 2 and recently bought Chinese BlueTooth intercom which works fine in intercom mode and connects fine to my phone in BT mode. However TomTom only detects original Scala, one which was included with satnav, but not my new one.
Is there any way to connect other BT intercoms? Would this navcore help? I'm currently running NC9501a from
-
20th September 2021, 07:48 PM #16
I suspect that both use a different protocol than the one used with the Rider v2.
In any case, there is a lot written about this below, then it doesn't work yet but you may know why it doesn't work
In the worst emergency I still have a Cardo here, unfortunately the cap has been lost, but I assume there will be someone in your area who also has one for sale at one or other site
-
The Following 2 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
LTgoodevil (20th September 2021), OneLover (20th September 2021)
-
22nd September 2021, 11:56 PM #17
I have connected Cardo and Chinese intercoms to a TomTom Rider k2 and they all worked well, try installing this navcore 9501 Rider V5 that I have published to see if it works for you, first reset the previous intercom connections that you want to link.
Try and tell us please.
Note: On some occasion you have connected the intercom with the gps for the fifth or sixth time that it has been tested, if it says impossible to connect, repeat more times and remember that the intercom is in paring mode.Last edited by Masp; 23rd September 2021 at 10:39 PM.
-
The Following 1 Users Say Thank You to Masp For This Useful Post:
- [ Click To Expand ]
-
Orni (24th September 2021)
iGO R3 HERE EUROPE 2023.Q4
Thank you very much for the contribution