Results 21 to 30 of 55
-
15th March 2022, 09:14 AM #21
-
16th March 2022, 01:08 AM #22
If it is strange, what I would do to see where the serious problem comes from;
1 uninstall patch.
2 restore from factory .
3 or put in recovery mode, start by pressing pressed button up to black screen and then 3 fast button on button boot after connecting to PC and MDC restores, check may MDC install Lower version of navcore update to the newest, check that everything works fine.
4 Make sure sdmagic is well made.
5 Put the corresponding patch of the navcore and meta.txt that contains the map that aims to activate.
regards
-
16th March 2022, 08:26 AM #23
I have tried to restore from factory only and it worked. Thank you very much simba
-
16th March 2022, 11:23 PM #24
I'm glad it works for you, see what version of navcore you have and what version of patch you put.
regards
-
16th February 2023, 12:46 AM #25
I have a Start 62 and a Go 400 Nav4, I updated with MDC to navcore 22.100.
I installed MSTMS-Nav4-Navcore22.100. I mention that this is not the first nav4 I unlock.
I downloaded the maps with TTActivator. I followed all the specified steps.
When I want to load the TTInstall.Mini-20200829 maps, it works up to about 40% and then closes.
I looked for navcore 21,200 but couldn't find it.
And I don't know how to change navcore.
The other IomIom had navcore 21,200 and worked perfectly.(4-5 devices.)
Any advice you can give me?
--------------------------------------------------------------------------------------------
I know where I went wrong.
I had SD Magic made for navcore 21,200, and I used it for 22,100.
Now I made another one for 22,100 and everything worked perfectly on both GO 400 and Start 62.
I realized that the data packages are not the same.
Thanks for your excellent work!Last edited by 07wnb; 16th February 2023 at 11:32 PM.
-
The Following 1 Users Say Thank You to 07wnb For This Useful Post:
- [ Click To Expand ]
-
simba (17th February 2023)
-
16th February 2023, 04:23 AM #26
navcore 22,100 updated, installed Patch 22,100, there should be no problems.
when you install new maps, keep the previous one? It stops in 40%, it may not have enough space. Put a microSD try to install a new map on microSD.
regards
-
16th February 2023, 01:24 PM #27
Uninstalled MSTMS-Nav4-Navcore22.100, reset to factory settings, now I have navcore 21.200.SD Card 16 GB .
I have installed MSTMS-Nav4-Navcore21.200 now I am installing the truck maps on the sd.
I'm at 20% and I'm waiting. I'll come back with information.
-
17th February 2023, 01:06 AM #28
Now I have another problem with Start 62.
Both with patch and without patch, when it receives GPS signal it freezes.
Inside, in simulation mode, it works perfectly.I read somewhere that meta.txt would be too loaded.
I left the meta only for the installed maps.If I reboot it, it starts normally but freezes again as it has a signal.
Is the problem software or hardware?
----------------------------------------------------------------
DONE! I solved it.
By mistake, I connected to MDC with the patch installed. I think I am introducing a BUG with the patch installed.I saw the same problem on another forum.
Solution:
1. Uninstall the patch
2. Reset the device to factory settings.
3.Enter Recovery Mode.
4. Connect to MDC. It will recover your device.
5. Do all the updates that MDC offers.
6. Reinstall MTSMS.
That's how I proceeded and now everything is perfect.
Now I have car maps in the internal memory and Truck on SD.
I found indications after a night of studying and surfing the Internet.
I hope it helps someone else.
Once again "Thanks"
Conclusion: DO NOT connect to MDC with patch installed!
I solved it before I read your post, but thanks. Now we definitely have the solution.
For those who have the same problem.Last edited by 07wnb; 17th February 2023 at 10:37 PM.
-
17th February 2023, 10:04 PM #29
iIf there have been similar cases, I do not remember the solution well.
if you have a patch, uninstall, restore with MDC (keep button on to black screen and 3 fast clicks on button on) after restor that has installed anterior Navcore, if it still does not receive a signal, it would have to check it more in depth of broken or loose hardware.
if when restorating satellite and loses it when you install Patche, make sure you have the same version of Navcore and Patch.
regards
-
The Following 1 Users Say Thank You to simba For This Useful Post:
- [ Click To Expand ]
-
07wnb (17th February 2023)
-
18th April 2023, 08:09 PM #30
charging battery...
Last edited by monte2023; 18th April 2023 at 08:54 PM.
UM - Trucker POI Professional...
hello could someone share the ttokg - Trucker...