Results 11 to 20 of 55
-
22nd January 2024, 01:10 PM #11
Hi Peter,
I checked the properties of my TomTom device, I have enough memory but I'll double check later tomorrow and let you know.
I have navcore v9.540 from memory. but can double check.
-
The Following 1 Users Say Thank You to bondy99 For This Useful Post:
- [ Click To Expand ]
-
PeterHimself (22nd January 2024)
-
22nd January 2024, 06:34 PM #12
So - to have some "clear" result about your experiences, work in Device2 maps for Device3 with no complications? Or are some limitations?
-
22nd January 2024, 06:41 PM #13
When the parts that are not used are removed, it should work normally.
If you have enough space to install the map, no adjustments are necessary
-
The Following 3 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
bondy99 (23rd January 2024), PeterHimself (22nd January 2024), Steve25 (22nd January 2024)
-
23rd January 2024, 02:40 PM #14
I had no complications going from Map 2 device to Map 3 device except street names and roads were pronounced as different names, as mentioned earlier. Logan Reserve Road became Logistic Circuit, how this happened is beyond me, I've always used light green maps. Something in the Map 3 has caused it. After trial and error I went back to the old map in the Map 2 device and all street and road names were correctly spoken..that is Logan Reserve Road is spoken as Logan Reserve Road.
I'll have another go at installing Map 3 again in the next day or two and road test again. I'll report back what transpires. Cheers.
-
The Following 1 Users Say Thank You to bondy99 For This Useful Post:
- [ Click To Expand ]
-
Steve25 (25th January 2024)
-
23rd January 2024, 03:04 PM #15
PeterHimself,
I can confirm the Navcore I have is v9.541.2-2042
-
The Following 1 Users Say Thank You to bondy99 For This Useful Post:
- [ Click To Expand ]
-
PeterHimself (24th January 2024)
-
23rd January 2024, 03:42 PM #16
-
The Following 1 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
bondy99 (24th January 2024)
-
24th January 2024, 10:38 AM #17
I'll redo the new map and see how it goes.
Let you know later tomorrow.
-
The Following 2 Users Say Thank You to bondy99 For This Useful Post:
- [ Click To Expand ]
-
pe1agp (24th January 2024), PeterHimself (24th January 2024)
-
25th January 2024, 02:22 PM #18
After deleting and reinstalling and adding the new cspeech AUS file, one again I was hearing street names that don't exist.
It's got me beat what the issue is. So back I go to the old nav 2 map.
-
The Following 1 Users Say Thank You to bondy99 For This Useful Post:
- [ Click To Expand ]
-
pe1agp (25th January 2024)
-
25th January 2024, 02:44 PM #19
-
The Following 1 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
bondy99 (25th January 2024)
-
25th January 2024, 02:54 PM #20
Yep, I will, in the meantime I've gone back to TomTom Australia v1110_11861. Everything works good on that map. Unfortunately lot of new suburbs have been built since.
I double checked my device, its TomTom XXL IQ Routes Edition.
Garmin City Navigator Europe NTU...
Welcome to the forum. Your device uses these NTU...