Results 11 to 20 of 33
-
12th November 2019, 02:39 AM #11
@Alfred_ML
I have now upgraded bootloader to latest version.......still the same problem with navcore 9.xxx but always a good thing to have the latest bootloader.
-
12th November 2019, 03:10 AM #12
Unfortunately, I think that you are very lonely at a great height with your problem.
What I wonder if the calibration information on the info screen. hold on / off as long as that screen appears, can be transferred to a calib.txt file.
By this I mean the data that becomes visible using the old situation.
While searching, I come across a manual how to act when wrong letters and / or numbers are activated, but that is not about half a screen shift.
However, I will publish it again here.
Touchscreen calibration
So, your TT does no longer give you an "a" when you enter an address or you have to press on weird spots in the menu to select something?
It usually means your digitser for the screen is partially faulty but you might be able to "fix" it without buying a new one.
All current Navcore can use a texfile "cal.txt", located in the root of the device to override the default calibration of the digitiser.
I will base my instruction on that and not on the cilb.txt for older Navcores (little bit different).
Ok, how do I know the values for the cal.txt?
Start your TT (best after a reset) and when the drums start press and hold the power button - this will show you the Linux status screen with all hardware related info.
Row 4 from the top shows your current bootloader, row 4 from the bottom shows the original calibration data of the digitiser.
Only the first values are of interest, the rest shows the voltage for the digitiser.
As an example from my device:
93 921 147 840
The values are:
93 = min X
921 = max X
147 = min Y
840 = max Y
One word of advise: the values inside the cal.txt are in a different order!
The sequence of the cal.txt is : Max X Min X Max Y Min Y
That means the 93 921 147 840 on the status screen translate to 921 93 840 147 inside the cal.txt!
With those values the will react exactly the same way as without the cal.txt present, if that is not the case check the values and the place again.
Keep in mind this is only an example and you have to use the values as shown on your status screen!
Normal touchscreens use a co-ordinate system and a point calibration, TT prefers to calibrate the start and end of the X- and Y- axis, so be prepared for a lot of reboots and changes inside the cal.txt!
I only describe how to calibrate the Y-axis, procedure is identical for the X- axis.
As by my example start changing the mx Y value.
If you lower the value the reaction on the screen should go down, if you increase the value the reaction should go more to the top of the screen.
Change the value by about 50, save the cal.txt in the root of your device and boot the TT.
You should notice a little difference already.
Try to remember by how much it has changed to get an estimate on how much further you need to change this value only.
Once you reach a point were you think it feel ok start the address input with the big keyboard for the finetuning.
Hint: If you notice after the changing the max value there is barely any change adjust it by about 200 and try again, if still no real change use the min value to start the calibration.
You now change both the min and the max value to get the most accurate result, using a touchpen is a good idea.
Only minor changes in the values should made at this stage and only one value at a time, otherwise you might end up messing around.
The final check should confirm the menu buttons work fine, all characters and numbers in the screen keyboard are assigned correctly and the zoom buttons in the map screen are working.
Don't be too disapointed to notice the keyboard works but the zoom buttons don't - they are very small and in the corners so only a perfect calibration will get them back working.
In case the input is off in both axes you should still start with the Y section to get the height correct before adjusting the x axis.
Changing both at the same time makes it really hard to figure out what change caused the reaction on the screen.
I hope this will to get your TT going again.
As a real world example:
The Y axis on tendriver's X20 was out of calibration & had to be lowered. The original Y values, on the Linux status screen, were: 134 856. After re-calibrating the Y axis back into alignment, the new Y axis values were 460 50. These new values were entered into the cal.txt file.
Keep in mind this is only an example, and you have to use the values as shown on your status screen!
-
The Following 1 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
Alfred_ML (18th November 2019)
-
12th November 2019, 03:15 AM #13
Another possiblbity:
EXPERIMENTAL
What it does is create the file cal.txt in the main directory if our device is decalibrated.
IF we have a decalibrated device:
We copy these two folders in the main directory of the device.
If you have a folder called sdkregistry, be careful that there are not more than 10 possible elections because
just read 10
We delete the calibP file if your screen is large or calibG if your screen is small.
Rename the file that remains as calib. You remove the P or the G.
Restart the device and select the Calibrate icon in the menu.
We will get a black window with a cross and we have to go pressing where this cross.
The device will be shut down and restarted with the file cal.txt
Test if it has served you.
In my go730 it works well for me.
-
The Following 1 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
Alfred_ML (18th November 2019)
-
12th November 2019, 03:38 AM #14
I ran the version you posted, and the screen is working YAY.
BIG thx.
Are there any similar version of 9.541?
-
12th November 2019, 03:51 AM #15
You're welcome and congratulations.
I don't have special version of 9.541, sorry.
I also wonder, is it really necessary to use 9,541.
If it concerns the WNRO problem then a flash update for the gps chip comes sooner in sight in my opinion
-
The Following 1 Users Say Thank You to pe1agp For This Useful Post:
- [ Click To Expand ]
-
Alfred_ML (18th November 2019)
-
12th November 2019, 02:30 PM #16
To all poster in this topic, thx for all help, really appreciate it.
-
12th November 2019, 02:42 PM #17
-
The Following 3 Users Say Thank You to biggerdave For This Useful Post:
- [ Click To Expand ]
-
-
18th November 2019, 02:30 PM #18
I'm not wrote anything about a bootloader update. But if you mean the update of the GPS firmware: this was urgently needed, but has nothing to do with the calibration of the screen.
After a total crash of another TT-device with subsequent screen misadjustment (the backup of this device don't solved this problem), this method was successful:
- delete all files and folders without file ttgo.bif in internal memory
- connect the device with TT-Home (without a memory card!)
- update to the oldest NC offered by TT-Home
- start the device and check the sreeen adjusting
- connect again with TT-Home and update to next offered NC and start the device to check the screen, do that until the 9.510 (if possible, 9.541 is absolutely not needed for your device). If the 9.510 should not be available, just take the 9.541
If your device now works with the 9.510, leave it at that. The 9.541 is absolutely superfluous and brings you no advantages!Last edited by Alfred_ML; 18th November 2019 at 02:37 PM.
-
The Following 2 Users Say Thank You to Alfred_ML For This Useful Post:
- [ Click To Expand ]
-
biggerdave (18th November 2019), pe1agp (18th November 2019)
-
19th November 2019, 04:19 AM #19
Hello! I also had the same problem with a GO730 with the 8,351 navcore, the screen was going well, and with the 9 .... bad. I tried to calibrate the screen, but it didn't respond well. The solution was to change the touch screen. and everything perfect, with the navcore 9 ... and new map.
Greetings!
-
The Following 1 Users Say Thank You to ovicon For This Useful Post:
- [ Click To Expand ]
-
pe1agp (19th November 2019)
-
19th November 2019, 07:17 PM #20
Maybe the current update of NC 9.541 for x20/30 has a bug. But why did you wait until today with the NC update? The 9.510 has been offered for many years by TT for these devices. And i never had screen problems on G0 730 (9.510) and Go 920 (9.702). The replacement of the touch screen may have helped you, but it was certainly superfluous.
P.S: You have updated your gps-chip firmware already to GSW3.2.5 after april 2019?
Garmin Topo France v6 Pro Entire...
Hello, as indicated by FireFox58 in his message...