Results 1 to 6 of 6
-
8th December 2016, 08:48 PM #1
Garmin GPSMAP 62s and GPSMAP 78s Setup
Clearing the Memory
Before you start mapping a farm, you need to clear the GPS’s memory. This means that no previously saved track logs or waypoints will be loaded onto your computer, which could be confusing when it comes to drawing your fields.
Clearing Saved Waypoints
This will delete ALL waypoints from your GPS. You should have downloaded any points you have previously collected and wish to keep to your PC, as waypoints will not be recoverable after they have been deleted.
To remove all waypoints:
1. Select the ‘Setup’ icon. Press ENTER.
2. Then select the ‘Reset’ icon and press ENTER.
3. Choose the ‘Delete All Waypoints’ icon and press ENTER.
4. When prompted select the ‘Yes’ icon and press ENTER to delete all the waypoints stored in the memory of the GPS.journeyx Reviewed by journeyx on . Garmin GPSMAP 62s and GPSMAP 78s Setup http://i.imgur.com/RSLv9LA.png Clearing the Memory Before you start mapping a farm, you need to clear the GPS’s memory. This means that no previously saved track logs or waypoints will be loaded onto your computer, which could be confusing when it comes to drawing your fields. Clearing Saved Waypoints This will delete ALL waypoints from your GPS. You should have downloaded any points you have previously collected and wish to keep to your PC, as waypoints will not be recoverable Rating: 5
-
The Following 1 Users Say Thank You to journeyx For This Useful Post:
- [ Click To Expand ]
-
quebec001 (16th May 2023)
-
8th December 2016, 08:49 PM #2
Clearing the Current Track Log
1. Select the ‘Setup’ icon and press ENTER.
2. Select the ‘Reset’ icon and press ENTER.
3. Select ‘Clear Current Track’ and press ENTER.
4. When prompted select the ‘Yes’ icon and press ENTER to delete the current track stored in the memory of the GPS.
-
8th December 2016, 08:49 PM #3
Setting the GPS Mode to Normal
There are several modes your GPS can run under: ‘Normal’, ‘Battery Saver’, ‘GPS Off’ and ‘Demo’. It is important that you have the GPS set to ‘Normal’ while mapping, as this setting updates your location most frequently.
To set your GPS to ‘Normal’ mode:
1. Power on your GPS.
2. Press MENU to get to the main menu screen (you may need to press MENU twice to quickly get to the menu screen).
3. Navigate to ‘Setup’ and press ENTER.
4. Press ENTER while the ‘System’ icon is highlighted.
5. Make sure that it says ‘Normal’ beneath the ‘GPS’ heading (at the top). If it doesn’t, press ENTER while the ‘GPS’ heading is highlighted and then select ‘Normal’ and press ENTER again.
6. Press PAGE or QUIT to exit the system menu.
-
8th December 2016, 08:49 PM #4
Setting Track Recording Mode
The track recording method should be set to ‘Auto’ and ‘Wrap when full’ must be turned off.
To set the track recording mode steps:
1. Press MENU twice to enter the main menu.
2. Using the rocker pad, make sure that ‘Tracks’ is selected and press ENTR.
3. Make sure that ‘Record Method’ is set to ‘Auto’. If it is not, use the rocker pad to highlight the setting, press ENTR. Using the rocker pad highlight ‘Auto’ then press ENTR again.
4. Press QUIT twice to get back to the main menu.
-
8th December 2016, 08:49 PM #5
Turning the Track Log On or Off
1. Select the ‘Setup’ icon.
2. Select the ‘Tracks’ icon.
3. Then select the ‘Track Log’ icon.
4. Then select the ‘Record, Do Not Show’ or ‘Record, Show On Map’ icon to setup how you would like the track to be stored and displayed.
-
8th December 2016, 08:50 PM #6
Recording a Waypoint (Angle Post)
1. While holding the GPS over the post, press the Mark button.
2. Press ENTER on ‘Done’. The waypoint numbers will increment automatically each time you save a new waypoint.
3. Or if it is a special feature that you want to remember later on toggle to the icon name ie.001. Press the ENTER button and rename.
4. The waypoint is now recorded and you may proceed to the next angle in the fence line where you will repeat this process again.
If you notice that the bars showing the GPS accuracy have a red cross through them the GPS will not record your point accurately.
The ‘red cross’ means it could not lock onto any satellites. The easiest way to correct this is to turn the unit off then restart the unit once you are out in the field.
Your GPS Set-up is complete!
Garmin Topo France v6 Pro Entire...
Hello, as indicated by FireFox58 in his message...